Nonlinear correlation between RMB internationalization and nonferrous metal prices

The correlation between Renminbi (RMB) internationalization and nonferrous metal prices was studied using the nonlinear Granger causality test and the dynamic conditional correlation-generalized autoregressive conditional heteroskedastic (DCC-GARCH) model. The results indicate that the relationship between RMB internationalization and nonferrous metal prices reflects a complex nonlinear mechanism. There was no mutual influence between RMB internationalization and nonferrous metal prices prior to the trials of the RMB settlement in the cross-border trade in July 2009. Since then, however, a bidirectional causal relationship between RMB internationalization and the price of copper and a unidirectional causal relationship from the price of aluminum to RMB internationalization were examined. In addition, due to the impact of extreme events, such as economic and financial crises, RMB internationalization and nonferrous metal prices are not always positively correlated but are rather occasionally negatively correlated.     

安规测试仪用于塑料制品探伤检测

该文介绍了传统的超声波、渗透和射线等绝缘体探伤方法,分析了它们的优缺点,针对其缺点,提出了用安规测试仪探伤塑料制品的方法。实验中,设置安规测试仪为拉弧停止,试验检测合格品的最高耐受电压,高压扫描塑料制品,筛选出不合格品。其过程简单、高效、快速、准确而且经济适用,可以通过改造测试探头适应不同的塑料制品,能取得不错的检测效果。     

饱和尾粉砂动孔隙水压力发展特性试验研究

采用动三轴仪对内蒙古某尾矿库尾粉砂进行了动强度试验,研究了围压、相对密实度及固结比对动荷载作用下尾粉砂中孔隙水压力发展特性的影响。研究结果表明,随着固结比、相对密实度、围压的增大,动荷载作用下饱和尾粉砂孔压增长曲线形状由陡峭转变为平缓。随着围压及固结比增大,试样动力破坏形式从以孔压值为主要表征指标的液化破坏,转化为以动剪应变为主要破坏形式的软化破坏。动荷载作用下发生液化破坏的饱和尾粉砂孔压增长过程分可为初始增长阶段、稳定增长阶段和快速增长至破坏阶段,孔压增长曲线表现为明显的反S型,本文采用双对数函数对该试验孔压增长曲线进行拟合,结果表明该模型可以较好地模拟尾粉砂在动荷载作用下的孔压发展规律。     

Improved district heating network operation by the integration of high-temperature heat pumps

Biomass combined heat and power (CHP) plants connected to district heating networks are a very good opportunity to increase the share of renewable sources into energy systems. Frequently, important consumers are connected to ensure a stable base heat demand throughout the year but they often have higher requirements in terms of temperature (i.e. steam), which involves a high level of temperature in the district heating network during the whole year and high levels of heat losses in the network. This contribution presents the possibility to decrease the level of temperature at which the district heating network operates and to use high-temperature heat pumps connected locally at the consumption point to produce steam when it is required. An investigation of the global design and integration through thermodynamic simulation models is realised for the University of Liège district heating network. This study is intended to determine the heat pump coefficient of performance and, therefore, to assess the balance between the savings in terms of heat losses and the additional heat pump electricity consumption.     

A method for testing the interface toughness of ceramic environmental barrier coatings (EBCs) on ceramic matrix composites (CMCs)

A simple interface fracture test for ceramic environmental barrier coatings (EBCs) on ceramic matrix composites (CMCs) was developed. A variation on the asymmetric double cantilever beam (ADCB) test was proposed so that the interface toughness could be measured in a small specimen of simple shape without applying interlaminar loading to the CMC substrate. The proposed test was applied to an EBC consisting of a mullite layer and Si bond coat on a monolithic SiC substrate. A pre-crack was introduced by pop-in cracking, and then a notch overlapping the pre-crack was machined. The pre-crack was opened by inserting a wedge into the notch. From the critical notch opening displacement the crack starts to propagate, interface toughness is calculated. The measured interface toughness was 4.1?J/m2. Finally, the application range of the test was discussed and suggestions were made for introduction of the notch and pre-crack.     

钢轨交流闪光焊接过程过梁爆破特征分析

以高速摄影技术作为主要研究手段，研究钢轨交流闪光焊接过程过梁爆破特征，并结合热成像系统采集焊接过程温度场，以此为数据基础定量分析了钢轨交流闪光焊接过梁爆破特征. 结果表明,钢轨交流脉动闪光焊接工艺模式下，加速闪光阶段具有几个阶段中最高的闪光频次46.93次/s，脉动闪光阶段具有最低的闪光频次11.07次/s；连续闪光阶段闪光烈度为0.009 2 mm/次，是几个阶段中最强的，脉动阶段的闪光烈度最弱，为0.003 8 mm/次；从闪光加热因子来看，脉动阶段最高，符合了该阶段积累热量的主要目的；加速闪光阶段最低，是由于该阶段为了制造保护气氛产生的气化过梁带走了较多的热量；从闪光均匀度看，闪光最不均匀的阶段是闪平阶段，最均匀的阶段是脉动阶段，这恰恰说明了两待焊端面的微观平行情况在闪平阶段最差、脉动阶段最佳.